Sort by: View
Discussions | Replies | Latest Activity |
---|---|---|
Loose JointsNo matter what I do, I am not able to get a tight, strong joint after driving the screws when using the jig. I can break the joint apart ea… Started by Bob in Kreg Jig® Operation |
13 |
Oct 31, 2011 Reply by Shift |
Power or cordlessWe all use power drills to drill the holes thru the jig but is better to use power or cordless ( with the rachet set low ) to put the screw… Started by Bill Hooper in Beginners' Zone |
9 |
Oct 28, 2011 Reply by Johnny D. Rich |
WOW WHAT GREAT CUSTOMER SERVICEI was adjusting the clamp on my K3, when it fell into my hand. The lock nut was a little tight, but fell out with very little force on the… Started by Da Bull in Miscellaneous |
1 |
Oct 27, 2011 Reply by Cecil King |
special promotionsI wondering if there is any special promotion going on. I am intrested in purchasing a Kreg router table.I am trying to find the best pric… Started by will delaney in Kreg Jig® Purchasing |
14 |
Oct 26, 2011 Reply by John Schaben |
full drawer extentionsI've seen full drawer extensions placed in the middle, bottom and even top of the sides of the drawers. Anyone know if there is a set "rule… Started by Mike Swaga in General Woodworking |
1 |
Oct 26, 2011 Reply by Jay Boutwell |
building a garage door of sortsI have an old box trailer that used to be on a straight truck. the box is about 20 foot long, 10 eight foot wide and about 9 foot tall. the… Started by Mike Kahle in General Woodworking |
0 | Oct 25, 2011 |
Pocket Holes Not SmoothI am having problems with "CHADS" remaining on the rightside of the pocket holes. I'm using a DeWalt cordless on a K3 block mounted and ha… Started by JIM HOWE in General Woodworking |
3 |
Oct 19, 2011 Reply by Fins59 |
Post photos of your Toolboxx!If you got a Toolboxx and filled it up, lets see some photos. Curious how everyone is organizing their gear inside. I ended up also putting… Started by Bob Sanders in Other Kreg® Products |
0 | Oct 19, 2011 |
Floor squeaksAny thoughts on squeaky floors? Started by Mike Berger in Miscellaneous |
2 |
Oct 16, 2011 Reply by Mike Berger |
Visible markings on your Kreg JigI was woodworking today and had to change the drill collar and the height of the jig. With sawdust on the jig and only impressions for numb… Started by Don Grubish in Kreg Jig® Operation |
25 |
Oct 16, 2011 Reply by Rusty Berkebile |
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service