Kreg Owners' Community

I am trying to determine the name of a piece of specialty hardware. It consist of a screw at one end and a bolt at the other. You screw the hardware into a piece of wood and then you leave the bolt extended to attach something to the wood using a nut. I need to find some, but I do not know what is the correct name.

Thanks for any help.

Views: 432

Reply to This

Replies to This Discussion

Michael,

Its called a hanger bolt

Don

     I believe they  are  called water  closet bolts  used for  mounting  toilet  stools to the floor

These are often referred to as hanger bolts.

large

Commonly used with top/leg mounting plates

Waddell Angle Top Hardware Plate, 2752A

And corner leg / apron brackets

Surface Mount Corner Brackets for Table Aprons, 4 pack

Bonus round - the fastener that has the coarse threads on both ends is known as a dowel screw

Grip Fast® 5/16"-18 x 3" Zinc Coarse Thread Dowel Screw - 2 Count

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

I have a problem with a k3 & k4

K3 problem the threaded insert is lose and will not hold setting. The k4 is worn and  hard to use. I was think maybe epoxy the insert in place may fix it. I tried wood glue did hold. Anyone else had the same problem? The k4 I have thought about…Continue

Started by Gary roofner in Beginners' Zone Mar 14.

Anyone using the Kreg Miter Gauge? 3 Replies

I'm thinking about getting the Kreg Miter Gauge instead of building a sled for my table saw. I figure the miter gauge would have more uses and since the stock will ride on the saw table there is no drop off like with some crosscut sleds. And it…Continue

Started by Marshall Harrison in Other Kreg® Products. Last reply by michael evans on Friday.

Pocket holes aren't deep enough 1 Reply

I'm having trouble getting my pocket holes deep enough. I'm using the kreg j4 system and using 3/4" stock 1 1/2" wide. I have set my jig to 3/4" high for the stock and set my drill bit to 3/4" to the tip. I'm pretty new at using this and I thought I…Continue

Started by JUSTIN RICHARDSON in Beginners' Zone. Last reply by Dave Johnson on Saturday.

Adaptive Cutting System 10 Replies

I really like the Adaptive Cutting System (ACS) and hope to buy it soon. My table saw really scares me as I have a bad knee that likes to buckle on me at inopportune times. I can just picture it happening at the table saw and tossing me into the saw…Continue

Started by Marshall Harrison in Beginners' Zone. Last reply by Marshall Harrison Mar 10.

Product Reviews

Merry Christmas r3

 Hi all Santa left me one under the tree the elf thar made it must have had a bad morning because one gray tab is metric and the other one is imperial help Santa what do I do

thanks Eric 

Posted by Eric Kershaw on January 8, 2019 at 6:27pm — 1 Comment

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…

Continue

Posted by Glenn Revheim on April 5, 2018 at 5:57am — 5 Comments

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…

Continue

Posted by justin waldron on April 2, 2018 at 5:46am — 2 Comments

Kreg Foreman

I have built many kitchens and finally decided to buy the Foreman, because my latest kitchen consisted of 28 cabinets and I was over my hand hurting from all the drilling, moving the clamp etc., it seemed like a smart choice.

The…

Continue

Posted by justin waldron on January 8, 2018 at 4:05am — 2 Comments

© 2019   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_