Kreg Owners' Community

I was wondering how the easiest way to upload a 124 MG video is .If I do a regular upload Im sure it will take hour or there about..If I zip it it should be faster correct?? I no it depends on speed of computer  uploading speed
Thanks for replies I just uploaded a way to make your own pocket plugs if you are out in field working and run out of them

jens
Grandpas Workshop

Views: 159

Reply to This

Replies to This Discussion

Jens,
If you're uploading a video, I don't think you'll want to "zip" it first. This is a compression technology used for sending files over email primarily... I'd recommend re-encoding the video to a smaller size and/or lower framerate. This will reduce the file size of the video making it easier to upload.

Also remember, this community allows you to embed videos from YouTube or Vimeo... so you may want to try uploading it to one of those sources and go about it that way if you're having troubles!

Good luck,
KregRep
This is what I am going to do is redo the video and hopefully it will work.thanks

KregRep said:
Jens,
If you're uploading a video, I don't think you'll want to "zip" it first. This is a compression technology used for sending files over email primarily... I'd recommend re-encoding the video to a smaller size and/or lower framerate. This will reduce the file size of the video making it easier to upload.

Also remember, this community allows you to embed videos from YouTube or Vimeo... so you may want to try uploading it to one of those sources and go about it that way if you're having troubles!

Good luck,
KregRep
Hopefully this is going to make it





Jens Jensen said:
This is what I am going to do is redo the video and hopefully it will work.thanks

KregRep said:
Jens,
If you're uploading a video, I don't think you'll want to "zip" it first. This is a compression technology used for sending files over email primarily... I'd recommend re-encoding the video to a smaller size and/or lower framerate. This will reduce the file size of the video making it easier to upload.

Also remember, this community allows you to embed videos from YouTube or Vimeo... so you may want to try uploading it to one of those sources and go about it that way if you're having troubles!

Good luck,
KregRep
Jens,
you're going to want to go here instead:
http://kregjig.ning.com/video/video/newWithUploader
When I clicked on to the link and go to my folder where the video is at the video is not in there now if I go to simple loader II opens video .This is how I did the video and sent to you, Did it not work on your end because I previewed it here first an dit was playing ,I only looked at maybe 10 seconds.Maybe I need to download ning again
For anyone having trouble uploading video... please remember that per Ning's requirements your video must be no larger than 100MB in size, and must be either .mov, .mp4, .mpg, .avi, .wmv, .3gp, or.3g2 file formats.

If you have any trouble uploading, it may help to first upload the file to a service like YouTube or Vimeo first as they have less stringent upload guidelines. Once you have the file uploaded to YouTube or Vimeo they'll provide you with an 'embed' code which you can add to this Ning community to share with everyone else.
http://i4.ytimg.com/vi/k5VAxqzkmX4/default.jpg


I tried Vimeo or what ever rand it was not working it froze up at 99% .Then I tried You tube and it loaded but I'm not sure if this is the correct upload to you . I'm not much on computers Thank God I have a real nice woodshop and lots of top notch tools
http://www.youtube.com/watch?v=k5VAxqzkmX4

KregRep said:
For anyone having trouble uploading video... please remember that per Ning's requirements your video must be no larger than 100MB in size, and must be either .mov, .mp4, .mpg, .avi, .wmv, .3gp, or.3g2 file formats.

If you have any trouble uploading, it may help to first upload the file to a service like YouTube or Vimeo first as they have less stringent upload guidelines. Once you have the file uploaded to YouTube or Vimeo they'll provide you with an 'embed' code which you can add to this Ning community to share with everyone else.

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_