Kreg Owners' Community

There are lots of ways community members have discovered to make their own Pocket-Hole Plugs. Here are a few of the latest ones we've seen... please be sure to post any new ones you find, or concepts you come up with right here in this post where we can keep them organized and discuss how well each method works compared to the others...


Heath Jenkins' Homemade bandsaw jig:

http://kregjig.ning.com/photo/kreg-plug-jig?xg_source=activity

 

 

 

Chief's Flush-Cut Saw Method:

http://kregjig.ning.com/video/chief-s-shop-making-your-own-pocket-h...

 

 

 

Jens Jensen's Pocket Plug Jig

http://kregjig.ning.com/video/pocket-plug-jig

 

 

 

Rod's Pocket Hole Plug Cutter

http://kregjig.ning.com/photo/pocket-hole-plug-cutter (you have to buy the bit)

Views: 4304

Reply to This

Replies to This Discussion

Here's another method which utilizes a band saw, by member Roger Falconer:

http://kregjig.ning.com/photo/albums/making-pocket-hole-plugs

jajajaja really really nice!,

now.... my automation&engineering mind is in a working avalanche state! :D!!

Hi there I was wondering if you made that drill press bit or where did you purchase it?

my emaill address is buddierob@yahoo.ca

Its a plug cutter. It was purchased By Rod from Woodworker.com.

I am experimenting with the following method:

1. Use a small board with pocket holes drilled.

2. Drill holes thru bottom for screw clearance.

3. Apply paste wax to surface of board

4. Insert pocket hole screws (cut off short).

5. Insert 2 1/16 inches (approx.) length of 3/8 inch D doweling. I found that Oak was “truer” to the 3/8 inch. Pine samples I obtained were irregular. Also, I had to sand corners of dowel pieces where inserted.

6. Use band saw to cut flush to board. This is a real challenge. Still trying to figure a good method to do this without the band saw cutting into the board. The paste wax helps. Also, I had better luck with a 1/8 inch saw blade that seems to have less “wander”. Another problem is “burning” of the pieces that will limit the use of these surfaces for those that are painted, or partially hidden.

7. After sawing, place board in horizontal position in vise, and use punch to drive out the piece and the pocket hole screw.

 A benefit is the “cut-off” pieces can also be used as plugs where less accuracy is needed… I rated these as “B” pieces. The loss of the saw “kerf” introduces some inaccuracy but still can be useable. Perhaps Teflon or some other material could be substituted for the board with less tendency to be cut by the band saw blade. I also considered O rings bonded in place rather than screws. The problem is duplication of the thickness of the screw head…

 

 

Attachments:

Reply to Discussion

RSS

Need Help?

For Technical Support, call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm (CST). 

Videos

  • Add Videos
  • View All

Forum

What's On Your Wish List? 1 Reply

Started by KregRep in Community-Specific. Last reply by Brad Martin on Friday.

attaching track saw to Kreg Rip-Cut 1 Reply

Started by A Kain in General Woodworking. Last reply by KregRep Nov 14.

Full size bed 2 Replies

Started by Bigchief in Beginners' Zone. Last reply by justin waldron Nov 11.

Router Table Cabinet 2 Replies

Started by Steve Mitchell in General Woodworking. Last reply by Steve Mitchell Nov 7.

PVC Mouldings 3 Replies

Started by douglas E. Cooper in General Woodworking. Last reply by Don Foley Nov 6.

Product Reviews

Kreg K5 Jig Review

Posted by Daris R. on November 20, 2017 at 5:39pm

The Pocket Hole Joinery Book - Review

Posted by Daris R. on October 17, 2017 at 11:00pm

© 2017   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_