Kreg Owners' Community

I have a K4 Kreg Jig Master System. With the Dust Collection Attachment in place I find it almost impossible to loosen/tighten the brass (?) knurled screw (Drill Guide Pin) that holds the Drill Guide in place at the correct height setting, and I find removing the Dust Collection Attachment for each adjustment to kind of a pain.

If Kreg was to sell a replacement Drill Guide Pin with a square drive inset added - which would allow me to use the screw drive bit to loosen/tighten the Pin - I would buy it in a heartbeat!!!

Views: 123

Reply to This

Replies to This Discussion

Ken, 

Thank you for the suggestion.  Unfortunately we do not offer a pin like you are referring to at this time.  If you are having issues with removing the pin, you can try slightly lifting up on the drill guide block as you rotate the pin relieving the weight against it.  This should make it much easier to turn allowing you to loosen it easier.  

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Kreg Accu-Cut and Rip-Cut 4 Replies

First off tried to mention all this to Kreg via Email and just because I live outside the USA seems that the system does not work as they say phone number invalid, which is not.OK bought a Accu-Cut and set it up no problems there worked OK both…Continue

Started by Kenneth J Hunt in Other Kreg® Products. Last reply by Kenneth J Hunt yesterday.

Router bits 4 Replies

Tungsten carbide? Skill level is beginning woodworker

Started by MINICOOPERUSAF in Beginners' Zone. Last reply by Tim Grace on Monday.

R3 part

hi all can anybody help got r3 for Xmas and I have noticed that the gray tabs are different think somebody  in assembly was talking the piss day and I have 1 metric side and imperial side so they don’t match up hellllp plzericContinue

Started by Eric Kershaw in Beginners' Zone Jan 8.

Having issues with K5 5 Replies

I watched the setup videos, searched for information and spent half a day and can not get the clamp to hold.i tightened up the screws underneath in various stages up to fully tightened, makes no difference.I do not get the two clicks and I can slide…Continue

Started by Todd Caldwell in Beginners' Zone. Last reply by Glen S Jan 7.

Product Reviews

Merry Christmas r3

 Hi all Santa left me one under the tree the elf thar made it must have had a bad morning because one gray tab is metric and the other one is imperial help Santa what do I do

thanks Eric 

Posted by Eric Kershaw on January 8, 2019 at 6:27pm

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…

Continue

Posted by Glenn Revheim on April 5, 2018 at 5:57am — 4 Comments

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…

Continue

Posted by justin waldron on April 2, 2018 at 5:46am

Kreg Foreman

I have built many kitchens and finally decided to buy the Foreman, because my latest kitchen consisted of 28 cabinets and I was over my hand hurting from all the drilling, moving the clamp etc., it seemed like a smart choice.

The…

Continue

Posted by justin waldron on January 8, 2018 at 4:05am — 2 Comments

© 2019   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_