Kreg Owners' Community

I have been running into this frustration more and more lately. What is the best and most foolproof way to clamp stability into a joint so that it won't slip when putting in the pocket screw?

Views: 1386

Reply to This

Replies to This Discussion

I use the Kreg Klamps, according to their instructions,

and don't have any problems.

The joints align perfectly.

NOTE:

Insure there is adequate clamping pressure, so as to stabilize the work-pieces, so the joint doesn't slip, before installing the screws.

Do you mean the one that fits inside the hole? That does work quite well, until I have a hole pattern that doesn't allow that clamp to be near enough to the one I am screwing.

Bradley, 

The best rule of thumb when clamping your joint is to put the majority of your clamping pressure on the piece that is receiving the screw.  This is the piece that will do any of your moving once the screw starts to enter it.  If you have any other questions please let us know.  

Bradley,

I use a 2 clamp system.  First I clamp both pieces to my work bench typically with a padded "F" style clamp, placing the clamp over the joint between the piece with the pocket holes and the piece the screws will go into.  This insures the faces of both pieces remain flat.  Then I apply a second clamp positioned the same as if I was clamping the pieces together with glue and no screws.  This insures neither piece will move when the screw is installed.  This may seem like a lot of clamps, but it works for me.

Hope this helps, Don

Don -
If I were making a face frame or door the clamping would not be an issue. Where I am having a problem is edge to face like in making a carcass for a cabinet or a drawer box.
Bradley

I clamped a runner along a line that I squared back off the face frame. Placed the divider against that runner & put the screws to it.

The clamp that fits into the pocket hole works,, as you know,, very well for attaching the divider to the face frame.

One other way to go about it for smaller items like drawers is to use your bar clamps & assemble the box like a glue-up. Nothing moves that way.

I put clamps around a project and have a square to keep the joints precise.  It is like the picture from the internet. 

Bradley,

When assembling cabinet carcasses or similar projects requiring edge to face mounting I use corner squares from Rockler.  I clamp the two pieces to the square to keep them aligned, both flush and square.  I then still use a long clamp to hold the pieces together while driving the screws. Since the pocket holes are inside the carcass I use the assembly squares on the outside.

I came to use this process because I also glue my pocket hole joints, even though its not required.  I have the pieces glued together before driving the screws.  Once the screws are in I can release the clamps and use the screws to hold the pieces together while the glue dries. 

Oh yes, besides the commercially available assembly squares Rockler sells they can also be shop made.

Don

Screw two pieces of straight timber at 90 degrees on your workbench ,place frame in two the temporary frame clamp with downward pressure screw together.Hope this helps. 

I use corner  clamps on carcuses and kreg on face frames. I also seen some uses metal deck corner brackets and clamps. I am going to try.

I tried the trick from family handyman using a 5 inch L bracket . Here are pictures of a project I'm building using kreg joints clamped with this method.

Gary,

I recall reading that, or a similar article, and had to verify it for myself.

I checked some typical stamped & formed angle braces, normally found at home centers---

I found the angles WERE NOT true 90 degrees.

The angles were measured using an accurate precision machinist square.

BTW---the angles can flex, depending on the amount of load they are subjected to.

The BEST I've found for assembly squareness, is using the "clamp-it" squares, offered by Rockler.

They're TRUE, of rigid construction, and feature reinforcing ribs.

These are my GO-TO squares for clamping frames, cabinet boxes, and the like.

Also available in the mini size.

Great for drawers, where the larger size is to big to fit inside of a box/frame.



Gary roofner said:

>>>I tried the trick from family handyman using a 5 inch L bracket ..../p>

 

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

I have a problem with a k3 & k4

K3 problem the threaded insert is lose and will not hold setting. The k4 is worn and  hard to use. I was think maybe epoxy the insert in place may fix it. I tried wood glue did hold. Anyone else had the same problem? The k4 I have thought about…Continue

Started by Gary roofner in Beginners' Zone Mar 14.

Anyone using the Kreg Miter Gauge? 3 Replies

I'm thinking about getting the Kreg Miter Gauge instead of building a sled for my table saw. I figure the miter gauge would have more uses and since the stock will ride on the saw table there is no drop off like with some crosscut sleds. And it…Continue

Started by Marshall Harrison in Other Kreg® Products. Last reply by michael evans on Friday.

Pocket holes aren't deep enough 1 Reply

I'm having trouble getting my pocket holes deep enough. I'm using the kreg j4 system and using 3/4" stock 1 1/2" wide. I have set my jig to 3/4" high for the stock and set my drill bit to 3/4" to the tip. I'm pretty new at using this and I thought I…Continue

Started by JUSTIN RICHARDSON in Beginners' Zone. Last reply by Dave Johnson on Saturday.

Adaptive Cutting System 10 Replies

I really like the Adaptive Cutting System (ACS) and hope to buy it soon. My table saw really scares me as I have a bad knee that likes to buckle on me at inopportune times. I can just picture it happening at the table saw and tossing me into the saw…Continue

Started by Marshall Harrison in Beginners' Zone. Last reply by Marshall Harrison Mar 10.

Product Reviews

Merry Christmas r3

 Hi all Santa left me one under the tree the elf thar made it must have had a bad morning because one gray tab is metric and the other one is imperial help Santa what do I do

thanks Eric 

Posted by Eric Kershaw on January 8, 2019 at 6:27pm — 1 Comment

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…

Continue

Posted by Glenn Revheim on April 5, 2018 at 5:57am — 5 Comments

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…

Continue

Posted by justin waldron on April 2, 2018 at 5:46am — 2 Comments

Kreg Foreman

I have built many kitchens and finally decided to buy the Foreman, because my latest kitchen consisted of 28 cabinets and I was over my hand hurting from all the drilling, moving the clamp etc., it seemed like a smart choice.

The…

Continue

Posted by justin waldron on January 8, 2018 at 4:05am — 2 Comments

© 2019   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_