Kreg Owners' Community

Making kitchen cabinets for the first time and having a blast.  Got the uppers done and mounted.  What a breeze with the Kreg system.  I have two questions (only one of 'em is specific to Kreg, but thought I'd ask the brain trust here)

1.  Using high grade ply for the drawers (1/2") and only have fine thread 1" screws that came in the screw assortment pack I bought)  Can I use fine in ply?

2. Drawer slides- Making drawers and I have the relief on the sides (1/2" for the slides).  Question is - Is there a setback for the top and bottom nedded to get the drawers out once installed?  Using Accuride Model  3832C.  They appear to just release and pull out straight, but wanted to check.

Thanks - Learning a lot with this project, but pretty happy with the outcome so far.


Views: 258

Reply to This

Replies to This Discussion


I would not recommend using the 1" fine thread screws with your plywood material as these will strip out easily during assembly. For this application I would use coarse threaded screws.  You will also need to make sure that your plywood is a true 1/2" thick. Most conventional plywood will be undersized and will take some adjustments with the settings via trial and error to get the best joint.  

As far as the slide, if you go to you can see the recommended setback by the manufacturer. If you have any additional questions please let us know. 

FWIW, I agree with the Kreg CS.

Also, I'd glue the joints. Oh, and most slides aren't very forgiving, especially regarding width and parallel.

Good luck and enjoy!

have to agree about using the fine screws; i would only use them in hardwoods. they're just not made for ply or soft woods. in my experience with drawer slides (having said my share of bad words while working with them), the front setback will depend a lot on your drawer face (inset? overlay?). i usually don't worry about a rear setback; i buy my slides about 1" less then the depth of the drawer box.

and now that i think about about slides being unforgiving on the width! i finally found that making my drawer box 1 and 1/32" less than the width of the opening makes installing the slide less painful. you can shim the width of a piece of paper easier than planing or sanding said width. also if your drawer box is EXACTLY 1/2" less on each side, you risk the screw heads getting in the way of a nice, quiet drawer slide.

Reply to Discussion


Need Help?

For Technical Support, call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm (CST). 


  • Add Videos
  • View All


Toy box 2 Replies

Started by David J Agler in Beginners' Zone. Last reply by KregRep Oct 13.

Clamp and glue thin borders 3 Replies

Started by Don Anderson in Beginners' Zone. Last reply by Ken Darga Oct 7.

routers and router stands 7 Replies

Started by tom hagan in Beginners' Zone. Last reply by tom hagan on Wednesday.

Router guide

Started by Scott taube in Beginners' Zone Sep 26.

problem joining a table leg to the base 3 Replies

Started by Bradley Smith in Beginners' Zone. Last reply by Trace Farthing Sep 12.

Product Reviews

The Pocket Hole Joinery Book - Review

Posted by Daris R. on October 17, 2017 at 11:00pm

Kreg Mobile Project Center

I just picked up my new Kreg Mobile Project Center Item #KWS1000.

Wow!  I set it up in my basement and it is great addition to my Kreg items.  I was viewing a video where a review on this fine product was being made, which prompts…


Posted by John Tomkinson on May 5, 2017 at 5:34am — 2 Comments

© 2017   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service