Kreg Owners' Community

A lot of plans I have found say that you shoudl use 1.25 inch Kreg screws for holes drilled at the 3/4 inch setting.  I find that these don't hold though and it is better to use the 1.5 inch screws.  IS it me doing something wrong that means I need the bigger screws or are plans I am looking at suggesting the wrong size screws?  What does everybody use for the 3/4 inch setting?  Thanks

Views: 12886

Reply to This

Replies to This Discussion

1.25 is the correct size for 3/4 inch wood Hard wood requires a fine thread screw and soft wood a course thread

Hi Andy. The 1 1/4" screw is the standard size for 3/4" stock. The 1 1/2" screws often push too far into the mating piece, which can cause the screw to poke through or "bump out" the face.

Check that your jig and stop collar settings are correct so that you are drilling the pocket hole to the correct depth. Always set the stop collar by aligning the step on the drill bit with the thickness mark, not the tip of the drill bit.

Also make sure that you are using the correct screw. As Bruce said, coarse thread is best for softwoods (and plywood), and fine thread for hardwoods--the more aggressive coarse thread can cause splitting in hardwoods. Make sure, too, that your clutch is not set too high. This can cause you to over-tighten the screw and strip the threads that the screw cuts into the wood.

Of course, experimentation is always the key to success, and if you are able to use a longer screw without problems, you can do that. In years of experimenting here at Kreg, and in many of my own projects, though, we find that the 1 1/4" screws are the best choice for 3/4" stock.

KregRep

I have had the same problem. I have used the Kreg system for a few years now and know that I have all the settings done correctly. I have never had any problems with ANY other sizes other than 3/4" material. I too have went over to 1 1/2" screws and it has solved my problem. You just have to make sure you do not tighten too tight and cause the screw to come through the face of your project as mentions by the Kreg Rep in the other response.

I was just do some craftsman style window frames & the 1 1/4" wouldn't catch, very loose and not holding tight. My work around was after I ran the screw in, I would replace it with a 1 1/2" screw that I clipped the front point off.  Seemed to work for me, who knows if you don't try you don't know!

I've used the 1 1/4" screw for years, even before Kreig was around.  I also always use some adhesive and never had a frame come apart.  We used the evans system tub for several decades, building cabinets.  Kreig has simplified and made the pocket hole system available for home shops as well as commercial shops.  Not even sure if evans is still around. 

May want to check and make sure your set up is correct, perhaps drilling a tad deeper so your 1 1/4" screw has more meat into the wood.   Good Luck.

Set up is correct, the grain of the wood I am joining is what causes the problem, hence the slightly longer screw.

As I said, this was my work around, not necessarily yours or the next guy. But I'm glad to see your interest in helping others, it is appreciated. That what makes us all better & strive to build bigger & better.

Carl

Maybe a dumb suggestion here, but make sure you don't have drill chips left in your pocket holes.  I have had some breakout and just adjusted the drill bit a little shorter than the gauge shows.  No problems with 1 1/4" screws into 3/4" material.  Makes a strong and tight joint for me.  Also, make sure your clutch is set just tight enough to bottom out the screws and not over-tighten.

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_