Kreg Owners' Community

I currently own router table #PRS1020. I recently purchased router fence #PRS1015. The instructions for the fence state that to attach the fence to a table other than #PRS1025 I have to modify my current table. I refuse to buy another Kreg router table that automatically works with the new fence.

Has anyone had to install fence #PRS1015 on table #PRS1020? If so, what modifications did you have to make?

Views: 260

Reply to This

Replies to This Discussion

Chuck, 

The main difference between the PRS1020 and the PRS1025 is that the PRS1025 will have a key hole at the end of the slot in the table to easily allow you to remove the fence.  Without this slot you would have to completely remove the lock down handle each time you wish to remove the fence.  Also the pre-drill holes for the clamp block to attach to the table would not match up to the hole pattern for the clamp block on the PRS1015.  All you would need to do is pre-drill your own holes at the correct spacing.  

Reply to Discussion

RSS

Need Help?

For Technical Support, call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm (CST). 

Videos

  • Add Videos
  • View All

Forum

Puzzle Caddy/Board

Hello All - I'm looking for a plan for a puzzle caddy to replace the frail cardboard ones we've used in the past...large main area and two smaller sorting/storing trays. If anyone has such a plan or has seen one someplace, I'd love to hear about…Continue

Tags: puzzle, Project

Started by R.J. Foster in Miscellaneous Dec 4.

Edge Joining 2" Boards 1 Reply

Hi Everyone,I appreciate all the threads on the community. I've got to use this more, you guys are great.I got my hands on some beautiful ambrosia poplar, 2 inches thick, that I want to join for a desk/counter top. Using the 2.5 inch screws and…Continue

Tags: joining, edge

Started by brian lazenby in Beginners' Zone. Last reply by Brad Martin Dec 1.

What type screw to use for Black Walnut 2 Replies

I have some 2" x 6" Black Walnut and need some 2 1/2" screws. To best of my knowledge Walnut is a hardwood so I need to use fine thread screws. However I can not find that length of Fine thread screws on Kregs website. Does anyone know where I can…Continue

Started by Duane Heda in Other Kreg® Products. Last reply by Duane Heda Dec 1.

Working in carport? 2 Replies

I share a large shop with a friend at his house, but, for the last couple years I have hardly been there to work on anything.I have moved a lot of the duplicate tools into my carport and have been working there.Does anyone else work in the…Continue

Started by Steven Brown in Miscellaneous. Last reply by Darrell Wertz Dec 4.

Product Reviews

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…

Continue

Posted by Glenn Revheim on April 5, 2018 at 5:57am — 4 Comments

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…

Continue

Posted by justin waldron on April 2, 2018 at 5:46am

Kreg Foreman

I have built many kitchens and finally decided to buy the Foreman, because my latest kitchen consisted of 28 cabinets and I was over my hand hurting from all the drilling, moving the clamp etc., it seemed like a smart choice.

The…

Continue

Posted by justin waldron on January 8, 2018 at 4:05am — 2 Comments

Kreg K5 Jig Review

Posted by Daris R. on November 20, 2017 at 5:39pm

© 2018   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_