Kreg Owners' Community

Tungsten carbide? Skill level is beginning woodworker

Views: 254

Reply to This

Replies to This Discussion

I started with the cheap assortment pack of 1/4" shanked bits from a store somewhere. Been so long I don't know where they were bought at. They will work just fine. Just take your time & make multiple passes getting to where you want your finished profile. Practice on different scrap species & router speeds to get a feel for feed rates of different woods. Most of all keep asking questions.

The best router bit advice I've read is to invest in a decent lower cost router bit set when a beginner (I chose the MLCS 8377 1/2" shank 15 piece router set - which are carbide tipped), and then replace those bits that you use most - as they wear - with higher end router bits (Whiteside, Freud, ...). 

I can't speak to whether or not the "higher end" bits are really that much better. Hopefully others can help with that.

@glens and @kenkortch thank you both for the replies. Great advice 

Yes, they are.  The carbide from the Freud Quadra-cut bits leave an incredibly smooth finish.  I do have a couple of Whiteside bits that also leave a very smooth cut - much better than the Skil or Bosch bits they replaced.

I still use most of my Skil and Bosch bits.  I do clean my bits and hone the faces from time to time with a diamond hone.

Do look on line for a speed chart.  Mine is out in the shop, so can't refer to it.  Basically, your fastest speeds are for bits under 1¼" in diameter in hard woods. Bits over 1¼" in hardwoods should use a speed a bit slower.  In soft woods, the speed would be a bit slower.  

IIRC, For my DeWalts, the speed dial (numbered 1-6, I can't remember what the actual RPM is) should be "5" for the 1¼" bits in hardwood, "4" for >1¼" bits in hardwood, "4" for <1¼" bits in soft woods and "3" for >1¼" bits.  DeWalt also has recommendations for other bits, but I don't use them often enough to remember anything.

Ken Kortch said:

The best router bit advice I've read is to invest in a decent lower cost router bit set when a beginner (I chose the MLCS 8377 1/2" shank 15 piece router set - which are carbide tipped), and then replace those bits that you use most - as they wear - with higher end router bits (Whiteside, Freud, ...). 

I can't speak to whether or not the "higher end" bits are really that much better. Hopefully others can help with that.

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Jig settings for 2 ¾ x 1 ½ boards with 30 degree miters?

I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters.  What setting on the Jig should I used? 1 ½ is too much.  Thanks.Continue

Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.

40mm Cup Hinge Jig Question

Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue

Started by Ed Anderson in Beginners' Zone Oct 3, 2023.

Product Reviews

New Kreg 720Pro

I saw the video Kreg put out for this new jig and had high hopes for it.

I purchased one today and am very disappointed with it.

First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…

Continue

Posted by Duke Leon on February 15, 2021 at 9:00pm

Not Pleased With Pocket Hole Construction

Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction.  I have considerable experience with conventional…

Continue

Posted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments

© 2024   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_