Kreg Owners' Community

I recently purchased a 6" clamp. It takes two hands to close it and the adjustment has little effect. It was manufactured in China and displays in a grey plastic clip for hanging in the shop. Another in the shop has the same problem. Is this a batch problem?

Views: 2411

Reply to This

Replies to This Discussion

Your clamps may be defective, Marcus. Please contact Technical Support at toll-free 800-447-8638 or technicalsupport@kregtool.com for help troubleshooting. 



KregRep said:

Your clamps may be defective, Marcus. Please contact Technical Support at toll-free 800-447-8638 or technicalsupport@kregtool.com for help troubleshooting. 

Thanks KregRep. I live in SW Australia (Perth). Carba-Tech is a local distributor. They will replace it when I demonstrate the problem when next in their store. All my other Automaxx clamps work to specifications including a 6" one. I like to adjust so that it is a one-hand operation. Currently I'm working on the rails and balusters around a 7x4m deck using pocket holes screws. Lots of holes and screws! Is there a recommendation for lubrication of the clamps?

KregRep said:

Your clamps may be defective, Marcus. Please contact Technical Support at toll-free 800-447-8638 or technicalsupport@kregtool.com for help troubleshooting. 

Marcus,

Have you tried "Dri-Lube"?

A spray-on material---dries rapidly and leaves a thin dry film of lubricant.

It works for me and has many uses in my shop.

I just received one Automaxx clamp included with the Mobile Center. I've tried clamping it down, but literally can't do it. Also tried adjusting the black screw all the way, both ways, with no effect.

I've got half a dozen other style Kreg clamps and know these work differently, but this just doen't see right.

I've even watched YouTube videos hoping I would find something I was not doing properly, but it seems awfully simple. 

Any thoughts?

Mike- Your clamp may be defective. Please contact Technical Support at toll-free 800-447-8638 or technicalsupport@kregtool.com for help troubleshooting.

Thanks,

KregRep


Mike Reese said:

I just received one Automaxx clamp included with the Mobile Center. I've tried clamping it down, but literally can't do it. Also tried adjusting the black screw all the way, both ways, with no effect.

I've got half a dozen other style Kreg clamps and know these work differently, but this just doen't see right.

I've even watched YouTube videos hoping I would find something I was not doing properly, but it seems awfully simple. 

Any thoughts?

I have the 90 degree automax, and recently built a furniture, Using solid 2x6 pine, I too am unable to clamp. Actually, I managed to clamp it only once using EXTREME force, only to destroy the pocket hole. My lumber is 1 5/8" thick as opposed to the more common 1 1/2". Could the extra 1/8" in thickness cause the problem?

Kreg customer service contacted me and sent out a new clamp. I slid the replacement into the rail, and it clamped down just as it shows. Works great and I am totally impressed with Kreg Co. and their customer service!

Mike Reese said:

I just received one Automaxx clamp included with the Mobile Center. I've tried clamping it down, but literally can't do it. Also tried adjusting the black screw all the way, both ways, with no effect.

I've got half a dozen other style Kreg clamps and know these work differently, but this just doen't see right.

I've even watched YouTube videos hoping I would find something I was not doing properly, but it seems awfully simple. 

Any thoughts?

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Adaptive Cutting System

I really like the Adaptive Cutting System (ACS) and hope to buy it soon. My table saw really scares me as I have a bad knee that likes to buckle on me at inopportune times. I can just picture it happening at the table saw and tossing me into the saw…Continue

Started by Marshall Harrison in Beginners' Zone 15 hours ago.

Ulimate K4 1 Reply

I really like my K4 pocket hole jig but I had a big cabinet project coming up so I wanted a way to clamp the boards to it faster than the toggle clamp alowed. I had seen some other people make pocket hole jigs with pneumatic cylinders in place of…Continue

Tags: k4, Pneumatic

Started by Iain Portalupi in Kreg Jig® Projects. Last reply by Marshall Harrison 15 hours ago.

Octagonal picnic table 1 Reply

Any plans available? Worked with wood before. Just got my Kreg5. Have a camp in the Adirondacks. Workshop there.

Started by MICHAEL FLANAGAN in Beginners' Zone. Last reply by R. E. Woods on Saturday.

Farmhouse Table Plans 2 Replies

Dear Kregeers,I would like to try and build a farmhouse table with extensions in the middle to seat 12.I have seen some plans on Ana White and Buildsomething, along with others. Unfortunately, most, if not all the plans are for extensions at the…Continue

Started by Lupe in Beginners' Zone. Last reply by Lupe Feb 12.

Product Reviews

Merry Christmas r3

 Hi all Santa left me one under the tree the elf thar made it must have had a bad morning because one gray tab is metric and the other one is imperial help Santa what do I do

thanks Eric 

Posted by Eric Kershaw on January 8, 2019 at 6:27pm

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…

Continue

Posted by Glenn Revheim on April 5, 2018 at 5:57am — 5 Comments

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…

Continue

Posted by justin waldron on April 2, 2018 at 5:46am — 2 Comments

Kreg Foreman

I have built many kitchens and finally decided to buy the Foreman, because my latest kitchen consisted of 28 cabinets and I was over my hand hurting from all the drilling, moving the clamp etc., it seemed like a smart choice.

The…

Continue

Posted by justin waldron on January 8, 2018 at 4:05am — 2 Comments

© 2019   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_