Kreg Owners' Community

I was assembling a cabinet today and screwed the screws into the other panel,the did the same thing on the other side and moved it slightly and every screw blew out of the panels all 8,4 on each side,Looking at where the screw went into the panel it only caught maybe 1/8" on the edge of the panel. the panels are 1/2" thick BB ply. any Idea why this happened.I'm using the kreg jig K3 set at 1/2" and kreg screws says they are for 1/2".

Is this the right way to attach? I did A, but is B a better way?

Views: 384

Reply to This

Replies to This Discussion

Drill the pocket hole as shown in "B".

The screw should be directed "INWARD", away from the edge.

When a screw is directed toward the OUTSIDE edge, as in "A", it may blow thru. 

Make some tests with the drill bit boring a 1/16" shallower.

 I use the "micro jig" when joining 1/2" material.

It's a good practice to make sample test pieces, before proceeding to the final work-piece.

This method helps to insure you're getting acceptable results.  

Hello,

In that same situation, I've put screws in both ways, depending upon which way would make them harder to see.  For example, if the cabinet is against the wall then I'll put them in from the outside edge so you do don't see the holes from the inside.  I don't think which side you drive them from matters.  The bigger issue is getting enough of the screw into the joining material without going too far.

I think your best bet would be to take a couple pieces of scrap that are the same thicknesses of your actual cabinet sides and do some test fits.

I've often had to "tweak" my drill collar settings beyond what the jig recommends you to use.  Often, wood just isn't the thickness it is supposed to be due to moisture, metric/imperial differences, etc.

Cheers,

Dan

"B" is always better - points the screw into the 'meat' of the wood.

That said, you can often get away with "A" with thicker material. Probably 80% of the time with 3/4" ply.

Rare that "A" will reliably work with 1/2" ply.

Trust me, I've learned this lesson a few times when making drawers with 1/2 stock ;)

Reply to Discussion

RSS

Need Help?

For Technical Support, call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm (CST). 

Videos

  • Add Videos
  • View All

Forum

Edge joining 3/4 inch plywood 2 Replies

Started by Lynn Greff in Beginners' Zone. Last reply by Lynn Greff on Monday.

Where can I get a K3 owners manual.... 3 Replies

Started by John Chasse in Beginners' Zone. Last reply by John Chasse May 19.

HELP! Older Kreg Precision Router Fence, need parts! 1 Reply

Started by Dan Spaulding in Beginners' Zone. Last reply by Dan Spaulding May 17.

kreg production stop extension 1 Reply

Started by Pat Meeuwissen in Beginners' Zone. Last reply by Brad Martin on Tuesday.

Layout/Project Setup Table 11 Replies

Started by Todd J Michalec12@gmail.com in Beginners' Zone. Last reply by Brad Martin on Tuesday.

Product Reviews

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…

Continue

Posted by Glenn Revheim on April 5, 2018 at 5:57am — 4 Comments

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…

Continue

Posted by justin waldron on April 2, 2018 at 5:46am

© 2018   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_