Hi Folks
Newbie making his 2nd post. I want to build some wood boxes using 3/4" wood. The box will be 8" high, and approximately 18" wide by 14" deep.
I want the box to have mitered corners rather than butt joints.
I've seen Kreg Jig videos showing how to make 'picture frame' mitered corners.
Is there a video or web site that can help with using the pocket hole jig to make a wood box like that with mitered corners. I assume this will require shorter screws and changing drill stop depths.
Thanks
Jeff
Tags:
Take a look at these discussions
http://kregjig.ning.com/forum/topics/joining-boards?commentId=29001...
http://kregjig.ning.com/forum/topics/turning-corners-in-cabinets
As I suspected, I saw a comment stating that there may be too much material removed after making miter cut for pocket holed screws to get a good hold.
I'm going to play with some scrap wood this week in any case to see if smaller screws will get a good hold.
If I can't do miters, I'll butt joint the sides
Thanks
Jeff,
With mitered corners, I use biscuit joinery---
no exposed screws.
This gives it the best appearance.
Thanks Ken
I have a biscuit joiner and often have used it for boxes and shelving units
I haven't done miters with biscuits but will play around with some scrap stuff this week
Jeff
The easiest and strongest mitered box is one that is held together with glue and a full length spline, These can be made using either a router table and a slotting bit and or a table saw with the blade set at 45 degrees passing the miter ends across the blade set to cut a shallow groove and passed by the blade two times cutting a 1/4 in groove. You must cut all the corners with one setting and then reset the saw to cut at a 1/8" groove in a different location in the mitered piece. Both setting should be made to cause the slot to be cut near the center of the miter. Make the spline to fit the cuts. This is similar to that of a biscuit however much simpler to do and actually stronger. Glue the miters together and use either a band clamp or similar clamp to keep the joints tight. A simple way that I do on complicated and simple joints is a good roll of electricians tape. It is a plastic product and when stretched around the object it provides a cheap and a throw away clamp. Because it is a plastic glue will not stick to it and since it has a memory the tape tries to return to it original size and this makes your joint even tighter.
The spline joint would definitely have more surface area than biscuits.
my experience with biscuits is that they are extremely strong joints. I find it really easy to use the biscuit joiner - and it allows for slight bits of error since there is play with biscuits before they set and expand.
but the spline is something I want to experiment with. I have a slot bit for a router but rarely use a router these days except for creating moulding with roundover bits. But i might try it on my table saw and goof around it.
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
1 |
K5 Repair |
2 |
Keepsake Box |
3 |
Turned Wands |
4 |
Boxes |
5 |
Turned Pipes |
6 |
Pizza Cutters |
7 |
Bookmarks |
8 |
Coffin Shelf |
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service