Kreg Owners' Community

High all,

 My first posting on this board. I'm just putting together a shop area in my basement. I have a mitre saw on its own stand, Kreg router table, and a 10" drill press and now my Dewalt 7480 Table saw looking for a place in my plan. I'm looking to build a work table for all sort of uses, 3' x 6' basically, that I can seat it at one end. I've seen many pics on Pintrest of this setup but none of them had their fences on. My base is only 13"x30", but with the fence on and extended to 24" the rails extend to the right several inches, and I don't see that built in to any one of their plans. Am I missing something? Should I open up the area to its right, to let me use the fence in this way? 

Thanks in advance. 

Bill

Views: 978

Reply to This

Replies to This Discussion

Bill,

After researching the model saw you own, I think you hit the nail on the head.  To be able to use the fence to its maximum capacity you need to either open up the area to the right or mount your saw to the extreme right of the table, allowing for the fence to be extended.

Don

Hi Bill,

I have a similar DeWalt Saw. Take a look at the work bench I have posted on this site. Search for mobile work bench.    http://kregjig.ning.com/photo/albums/mobile-work-bench   Something like this may work?

Homer

Is there a remote change you still have the plans for that bench? I have a garage that is tightly packed to work in. I need something small and portable to help with the Saw Stop I am about to buy.

Homer Moyers Jr said:

Hi Bill,

I have a similar DeWalt Saw. Take a look at the work bench I have posted on this site. Search for mobile work bench.    http://kregjig.ning.com/photo/albums/mobile-work-bench   Something like this may work?

Homer

Sure do; i'll need your email and i will send it to you.

Homer

I appreciate you doing this. rebender_1@verizon.net

Thanks!

Bob

I am actualy building a bench similar to what you are describing. I saw the same pictures on pintrest and thought the same thing about the fence rail. what I am doing is I dropped the entire end of the bench lower so there isn't anything on either side of the table saw. I am then building a fold up top on the right side for use with wider cuts. when folded down i can use the stock fence. sorry i don't have pics yet. will post them when i finish it all up.

Reply to Discussion

RSS

Need Help?

For Technical Support, call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm (CST). 

Videos

  • Add Videos
  • View All

Forum

I have a question - I need your input 2 Replies

Started by Michael Meyer in Community-Specific. Last reply by Glen S yesterday.

Pneumatic conversion pocket hole 2 Replies

Started by Michael B in Beginners' Zone. Last reply by KregCS Feb 19.

Kreg Storage 2 Replies

Started by Jim Mahan in Kreg Jig® Projects. Last reply by R. E. Woods Feb 16.

Old Kreg Jig - K1?

Started by Kent Bruner in Kreg Jig® Purchasing Feb 11.

concealed hinge jig stop collar 1 Reply

Started by Joe Grane in Other Kreg® Products. Last reply by KregRep Feb 12.

Product Reviews

Kreg Foreman

I have built many kitchens and finally decided to buy the Foreman, because my latest kitchen consisted of 28 cabinets and I was over my hand hurting from all the drilling, moving the clamp etc., it seemed like a smart choice.

The…

Continue

Posted by justin waldron on January 8, 2018 at 4:05am — 2 Comments

Kreg K5 Jig Review

Posted by Daris R. on November 20, 2017 at 5:39pm

© 2018   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_