Kreg Owners' Community

Hello, has anybody in Australia managed to get hold of the Kreg KWS1000 Mobile Project Centre? I have tried Amazon but the freight was more than the tool cost and the local distributor, Carba-Tec don't have it and are't interested in helping. I assume this might change when Amazon open in Australia but that won't be until 2018.

Thanks.

Lee.

Views: 849

Reply to This

Replies to This Discussion

Hi Brad,

      It was a 135 degree plain twist drill.  Not as good as a counter-bore but it allowed the rivnuts to be flush.

Roger 

I got it around October last year. Overall, a good buy, but I am really bummed about the fact it is VERY far from being flat, and not adjustable.

Did someone succeed to adjust the wings to actually be a flat 180 degrees, and no more than that?

Thanks!

I am loving my work centre. True, the top isn’t flat but I wouldn’t expect it to be. It folds after all. The self adjusting clamp that comes with it is a real timesaver for me. I have since bought the Kreg accu cut and the rip cut jig. I find the method of attaching the saw to these to be truly awfull so I have the saws permanently with 5mm screws. I guess I don’t expect things to be 100% every time because they never are no matter who the manufacturer is.

Edward, 

The table top is not designed to be a completely flat surface.  It is designed to be a working surface and not a flat surface to be measured against.  While clamping your work pieces the material will be flat against the table and will not cause issues with your joint. With this being said, the table should not dip more than 1/4" from the center of the track to the edge of the table.  If it is more than this please either contact us directly or the dealer you purchased it from.  

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

I have a problem with a k3 & k4

K3 problem the threaded insert is lose and will not hold setting. The k4 is worn and  hard to use. I was think maybe epoxy the insert in place may fix it. I tried wood glue did hold. Anyone else had the same problem? The k4 I have thought about…Continue

Started by Gary roofner in Beginners' Zone Mar 14.

Anyone using the Kreg Miter Gauge? 3 Replies

I'm thinking about getting the Kreg Miter Gauge instead of building a sled for my table saw. I figure the miter gauge would have more uses and since the stock will ride on the saw table there is no drop off like with some crosscut sleds. And it…Continue

Started by Marshall Harrison in Other Kreg® Products. Last reply by michael evans on Friday.

Pocket holes aren't deep enough 1 Reply

I'm having trouble getting my pocket holes deep enough. I'm using the kreg j4 system and using 3/4" stock 1 1/2" wide. I have set my jig to 3/4" high for the stock and set my drill bit to 3/4" to the tip. I'm pretty new at using this and I thought I…Continue

Started by JUSTIN RICHARDSON in Beginners' Zone. Last reply by Dave Johnson on Saturday.

Adaptive Cutting System 10 Replies

I really like the Adaptive Cutting System (ACS) and hope to buy it soon. My table saw really scares me as I have a bad knee that likes to buckle on me at inopportune times. I can just picture it happening at the table saw and tossing me into the saw…Continue

Started by Marshall Harrison in Beginners' Zone. Last reply by Marshall Harrison Mar 10.

Product Reviews

Merry Christmas r3

 Hi all Santa left me one under the tree the elf thar made it must have had a bad morning because one gray tab is metric and the other one is imperial help Santa what do I do

thanks Eric 

Posted by Eric Kershaw on January 8, 2019 at 6:27pm — 1 Comment

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…

Continue

Posted by Glenn Revheim on April 5, 2018 at 5:57am — 5 Comments

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…

Continue

Posted by justin waldron on April 2, 2018 at 5:46am — 2 Comments

Kreg Foreman

I have built many kitchens and finally decided to buy the Foreman, because my latest kitchen consisted of 28 cabinets and I was over my hand hurting from all the drilling, moving the clamp etc., it seemed like a smart choice.

The…

Continue

Posted by justin waldron on January 8, 2018 at 4:05am — 2 Comments

© 2019   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_