Kreg Owners' Community

I bought a Kreg ProPack quite some time ago (years) and opened it up last night to use it. I want to join 1" stock. The jig I have is set up to join 1/2, 3/4 and 1 1/2 in stock but not 1" stock. How do I use this jig to join 1" stock.

Views: 244

Reply to This

Replies to This Discussion

Though I seldom use 1" stock, when I do I just use the settings for 3/4 and use glue. Or you can shim the stock until you find a setting that will cause the screw to exit in the middle of the stock, then choose a screw that will give you the amount of penetration you feel is necessary. It's easy if you have a bit of scrap to play around with. I have been using the K2000 for years and have never felt a need to "upgrade". The only moving part on the K2000 is the clamp, sometimes simple is better.
Thanks for the advice, I was just getting ready to play with some different thicknesses to see what would happen. The only other thing I will need to play with is drilling depth, that won't be too hard. I used 1" lumber because it was for a window frame and that was the demension of the old one.

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

I have a problem with a k3 & k4

K3 problem the threaded insert is lose and will not hold setting. The k4 is worn and  hard to use. I was think maybe epoxy the insert in place may fix it. I tried wood glue did hold. Anyone else had the same problem? The k4 I have thought about…Continue

Started by Gary roofner in Beginners' Zone Mar 14.

Anyone using the Kreg Miter Gauge? 3 Replies

I'm thinking about getting the Kreg Miter Gauge instead of building a sled for my table saw. I figure the miter gauge would have more uses and since the stock will ride on the saw table there is no drop off like with some crosscut sleds. And it…Continue

Started by Marshall Harrison in Other Kreg® Products. Last reply by michael evans on Friday.

Pocket holes aren't deep enough 1 Reply

I'm having trouble getting my pocket holes deep enough. I'm using the kreg j4 system and using 3/4" stock 1 1/2" wide. I have set my jig to 3/4" high for the stock and set my drill bit to 3/4" to the tip. I'm pretty new at using this and I thought I…Continue

Started by JUSTIN RICHARDSON in Beginners' Zone. Last reply by Dave Johnson on Saturday.

Adaptive Cutting System 10 Replies

I really like the Adaptive Cutting System (ACS) and hope to buy it soon. My table saw really scares me as I have a bad knee that likes to buckle on me at inopportune times. I can just picture it happening at the table saw and tossing me into the saw…Continue

Started by Marshall Harrison in Beginners' Zone. Last reply by Marshall Harrison Mar 10.

Product Reviews

Merry Christmas r3

 Hi all Santa left me one under the tree the elf thar made it must have had a bad morning because one gray tab is metric and the other one is imperial help Santa what do I do

thanks Eric 

Posted by Eric Kershaw on January 8, 2019 at 6:27pm — 1 Comment

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…

Continue

Posted by Glenn Revheim on April 5, 2018 at 5:57am — 5 Comments

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…

Continue

Posted by justin waldron on April 2, 2018 at 5:46am — 2 Comments

Kreg Foreman

I have built many kitchens and finally decided to buy the Foreman, because my latest kitchen consisted of 28 cabinets and I was over my hand hurting from all the drilling, moving the clamp etc., it seemed like a smart choice.

The…

Continue

Posted by justin waldron on January 8, 2018 at 4:05am — 2 Comments

© 2019   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_