Kreg Owners' Community

First off tried to mention all this to Kreg via Email and just because I live outside the USA seems that the system does not work as they say phone number invalid, which is not.

OK bought a Accu-Cut and set it up no problems there worked OK both cutting the guide strips and also making another cut to check measurement was OK. When I cam to sweep up I came across a small screw and wondered where it was from, then found another and another, so three in all. It was only when I went to look on the underside of the track I found that three of the screw fitting had come away. Lucky I found them. I had tightened them before hand so how they worked loose I do not know. 

The Rip Cut today set that up and once the circular saw was fitted to the sled, was OK, then moved the saw blade next to the edge guide and then I found that the cursor is too small in the cursor lock to be able to line the red maker up to the start of the measurements, it falls out. should have been made longer. So the only way I can get it line up is to glue it in place. 

I wonder what is the next problem going to be.

Ken Hunt.

Views: 154

Reply to This

Replies to This Discussion

Ken, 

Thank you for reaching out to us on the issues you are having.  I was curious if you could send us some pictures of the issues with the Rip-Cut.  We just want to verify that it is set up correctly as we have not heard of this issue before.  I have sent you a friend request with a message that includes the email address to send the pictures to.  Thank you and hopefully we can get this resolved in a timely manner.  

Pictures next, have tried two ways, first if the Indexing Stop is in place then I have a gap between the saw blade and the Edge guide of about 4mm. If the stop is removed then it all lines up but still the cursor is right on its end of the lock. 

Sorry did not know the written text went ahead. Thank you for responding first off. I have tried to send pictures of what In was on about but when I sent the reply I got a message that was unable to load the pictures. I will try again and see what happens. Meanwhile I did get a hold of Kreg Technical team via email and have sent then some pictures and text as well. 

Hi again, sorry but the penny dropped into the slot now. If I move the Indexing Stop to the other side then it all fits well. Just did not dawn on me to do that. The cursor mind you is on its last two rungs with the Cursor lock. 

I am sorry if I have caused a fuss due to my stupidly. They say you live and learn. I thank you all for your interests and help. Bye for now Ken.

Reply to Discussion

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Octagonal picnic table 1 Reply

Any plans available? Worked with wood before. Just got my Kreg5. Have a camp in the Adirondacks. Workshop there.

Started by MICHAEL FLANAGAN in Beginners' Zone. Last reply by R. E. Woods yesterday.

Farmhouse Table Plans 2 Replies

Dear Kregeers,I would like to try and build a farmhouse table with extensions in the middle to seat 12.I have seen some plans on Ana White and Buildsomething, along with others. Unfortunately, most, if not all the plans are for extensions at the…Continue

Started by Lupe in Beginners' Zone. Last reply by Lupe on Tuesday.

60 inch Round Table 5 Replies

Hello my Kreg friends,I have been off this forum for some time now, but I am back.I have build a few children's 30" table and chairs - which I am very happy with the results.But now I want to build a 60" round dining table - using the Kreg system…Continue

Started by Marty Rosenbloom in Kreg Jig® Projects. Last reply by brinda Ashley on Friday.

Track Saw Cutting Board for Mobile Project Center - KWS1000 1 Reply

I've been using track saw systems for many years. I had Eurekazone system for probably 15 years and just this past year switched over to a cordless Makita system. I got rid of my EZ cutting bench and replaced it with a MPC. Liked it so much I bought…Continue

Started by Mike Goetzke in Other Kreg® Products. Last reply by David Hitt Jan 30.

Product Reviews

Merry Christmas r3

 Hi all Santa left me one under the tree the elf thar made it must have had a bad morning because one gray tab is metric and the other one is imperial help Santa what do I do

thanks Eric 

Posted by Eric Kershaw on January 8, 2019 at 6:27pm

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…

Continue

Posted by Glenn Revheim on April 5, 2018 at 5:57am — 5 Comments

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…

Continue

Posted by justin waldron on April 2, 2018 at 5:46am — 2 Comments

Kreg Foreman

I have built many kitchens and finally decided to buy the Foreman, because my latest kitchen consisted of 28 cabinets and I was over my hand hurting from all the drilling, moving the clamp etc., it seemed like a smart choice.

The…

Continue

Posted by justin waldron on January 8, 2018 at 4:05am — 2 Comments

© 2019   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_