Kreg Owners' Community

Hi,

I'm new to the site so my question may be a kinda stupid one.

I recently purchased the K4 master jig set for a project I'm working on.

I noticed that when I have the dust collection attachment fitted to the jig I cannot unscrew the screw that hold the depth jig in place without removing the dust attachment each time.

Any thoughts or suggestions on this?

Regards

JB

Views: 286

Reply to This

Replies to This Discussion

I brought this up a little bit ago here and didn't get much feedback.

I wish it had a square drive or even phillips head, but the only thing I can think of is to use a Dremel with a cutting blade and cut a slot across the head so I can use a slot screwdriver. I think I have one of those screwdrivers around here somewhere.

That leads me to wonder if I can buy a replacement thumb screw if I mess up the original one.

Ken

John, 

Thank you for your input.  With the dust collection attachment on the jig itself you can unscrew the index pin, though it is not as easy as without the dust collection attached.  The notched rim of this pin allows you to run your thumb across the top of it, loosening or tightening the pin to allow you to move the drill guide block with the dust collection attachment in place.  We do appreciate your comments as this is how we grow and improve our tools.  With that being said we have passed them on for further review.  

Hi Ken,

Thanks for your input, good point as I feel "running your finger over the knurled part of the screw" won't release it unless it wasn't tightened up very much in the first place?

I think the supply of an extended section of the knurled part of the screw would facilitate easy removal of the screw, only needs to be another inch or so longer.

Maybe Kreg could consider this

Only a small part of the whole tool I realise but it would make an already remarkable tool even better??

Regards

John

Ken Kortch said:

I brought this up a little bit ago here and didn't get much feedback.

I wish it had a square drive or even phillips head, but the only thing I can think of is to use a Dremel with a cutting blade and cut a slot across the head so I can use a slot screwdriver. I think I have one of those screwdrivers around here somewhere.

That leads me to wonder if I can buy a replacement thumb screw if I mess up the original one.

Ken

How about making that thumb screw square drive? 

KregCS said:

John, 

Thank you for your input.  With the dust collection attachment on the jig itself you can unscrew the index pin, though it is not as easy as without the dust collection attached.  The notched rim of this pin allows you to run your thumb across the top of it, loosening or tightening the pin to allow you to move the drill guide block with the dust collection attachment in place.  We do appreciate your comments as this is how we grow and improve our tools.  With that being said we have passed them on for further review.  

Reply to Discussion

RSS

Need Help?

For Technical Support, call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm (CST). 

Videos

  • Add Videos
  • View All

Forum

Missing clamping table project 3 Replies

Started by Brandon B. in Beginners' Zone. Last reply by jock sloan yesterday.

90 gallon aquarium stand

Started by Glenn Gilbert in Community-Specific Jun 11.

Proper clamping technique 1 Reply

Started by Ron Salgado in Kreg Jig® Operation. Last reply by KregRep May 31.

Edge joining 3/4 inch plywood 2 Replies

Started by Lynn Greff in Beginners' Zone. Last reply by Lynn Greff May 20.

Where can I get a K3 owners manual.... 3 Replies

Started by John Chasse in Beginners' Zone. Last reply by John Chasse May 19.

Product Reviews

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…

Continue

Posted by Glenn Revheim on April 5, 2018 at 5:57am — 4 Comments

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…

Continue

Posted by justin waldron on April 2, 2018 at 5:46am

© 2018   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_