Kreg Owners' Community

I've not been able to find information on how to do the following:
I'm building a table base. The legs are 5" square hard wood (receiving piece) the rails are 1.5" pine (through piece)
Since I'm screwing into the hardwood, I would think I should use fine threaded screws, but it looks like they only come in 1.5" length
That doesn't seem long enough. If legs were softwood, it would call for a 1.5" setup and 2.5" screws.
So, it looks like my choices are
A) 2.5" corse into the hardwood
B) 1.5" fine screws (will they hold?)

If B, what would the proper setup and stop collar be?

Terry

Views: 1081

Reply to This

Replies to This Discussion

Here's the response from support for future reference

Thank you for contacting Kreg Tool! Unfortunately, we do not have a 2-1/2" Fine Thread screw for thicker hardwood material. In cases like this you would want to use the 2-1/2" Course Thread screws and when you are driving them into your legs I would suggest to do the following: Drive the screw in a ways then back it out then drive it back in a bit more and then back it out and repeat until the screw is fully seated in the pocket hole.

Terry, 

Depending on the density of the hardwood you are using, the coarse-thread screws should work. However, it could cause your material to split. A safer option would be to set the jig up for 3/4" material and then use the 1 1/2" fine-thread screws. This would give you the most penetration while using the fine-thread screw. If you have any additional questions please let us know.  

Screw wax goes a long way in hardwoods. Don't ask me how I found out!! LOL

If wax is not available, try rubbing the screw-threads through a block of soap each time for lubrication.

Reply to Discussion

RSS

Need Help?

For Technical Support, call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm (CST). 

Videos

  • Add Videos
  • View All

Forum

LED Lighting on mobile bench

Started by Steven Baynes in Miscellaneous Oct 8.

Ridgid tools 1 Reply

Started by steve kidd in Beginners' Zone. Last reply by Glen S Oct 9.

Cabinets and the best wood choice for the carcass. 3 Replies

Started by Stephanie H in Kreg Jig® Projects. Last reply by Glen S Oct 2.

1x6 into a 4x4? 4 Replies

Started by Dave N in Kreg Jig® Projects. Last reply by Edward Weitsman Sep 29.

Rip-Cut Ruler 5 Replies

Started by Cynthia Alaniz in Beginners' Zone. Last reply by Glen S Oct 2.

Product Reviews

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…

Continue

Posted by Glenn Revheim on April 5, 2018 at 5:57am — 4 Comments

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…

Continue

Posted by justin waldron on April 2, 2018 at 5:46am

Kreg Foreman

I have built many kitchens and finally decided to buy the Foreman, because my latest kitchen consisted of 28 cabinets and I was over my hand hurting from all the drilling, moving the clamp etc., it seemed like a smart choice.

The…

Continue

Posted by justin waldron on January 8, 2018 at 4:05am — 2 Comments

Kreg K5 Jig Review

Posted by Daris R. on November 20, 2017 at 5:39pm

© 2018   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_