Kreg Owners' Community

That's right . . .  I am fuming some white oak with ammonia. This is a process that apparently was popular with some of the mission style/arts and crafts furniture makers years ago where white oak is exposed to ammonia and it darkens.

I am building a little cabinet out of quarter sawn white oak, and thought I would give this process a try. So, I procured some VERY high strength ammonia, poured some in a cup, and placed the cup and a scrap oak board inside a plastic storage container, and taped it all up. In just 24 hours, the wood got really dark! Darker than I really wanted it, to be honest. I put a stripe of masking tape over a portion of the piece, but the fumes went right through -- you can't even see where the tape was.

 

My question -- does anyone out here have any experience with fuming oak? I would like to get your input before I put my cabinet in a tent and start fuming again.

Views: 177

Reply to This

Replies to This Discussion

Hey William!!  I saw the process and it looks really cool, but I've never done it.  You're using aqua ammonia?  I saw it on YouTube, maybe you could take a look there and see if it helps?

Thanks for the YouTube info, Justin. I did go and look at that. The ammonia I got is ammonium hydroxide, 25%, and it is the nastiest smelling stuff you can imagine.

I did a test piece, and exposed it for almost 24 hours. I was expecting kind of a warm, golden color, maybe a little bit orange. But my test piece turned more of a gray - almost ashen looking. It did make the "fire" in the grain stand out, but the color needs some work.

There is supposed to have been an article in Fine Woodworking #126 about the process, and I have about the first 110 issues, but not that one.

From what I have read elsewhere, though, 24 hours should have been about the right amount of time.

 

I think I will try a few more test pieces with shorter exposure times, see how that goes.

Well, good luck and make sure you let me know how it turns out and I will do a little research too.
Hi William, I went to www.woodworkersjournal.com and searched fuming wood and there was several good articles there about it, good luck

Thanks, Ray, for the info. I read several of the articles, and am a bit encouraged that some say that the gray color will turn more brown once a finish is applied.

 

One thing I have already found: you don't have to use very much ammonia, and it will maintain an even color without setting out multiple containers of ammonia. I believe that if my shop was made of white oak, I could fume the whole place with about cup of this stuff.

 

Woodworker's Journal looks like a great source of info - I will keep that in mind in the future.

 

By the way, several of the articles mentioned the difficulty of finding a source for ammonia. I found a place on line called Art Chemicals (www.artchemicals.com) which wasn't cheap, but they have some potent ammonia!

Reply to Discussion

RSS

Need Help?

For Technical Support, call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm (CST). 

Videos

  • Add Videos
  • View All

Forum

Missing clamping table project 3 Replies

Started by Brandon B. in Beginners' Zone. Last reply by jock sloan yesterday.

90 gallon aquarium stand

Started by Glenn Gilbert in Community-Specific Jun 11.

Proper clamping technique 1 Reply

Started by Ron Salgado in Kreg Jig® Operation. Last reply by KregRep May 31.

Edge joining 3/4 inch plywood 2 Replies

Started by Lynn Greff in Beginners' Zone. Last reply by Lynn Greff May 20.

Where can I get a K3 owners manual.... 3 Replies

Started by John Chasse in Beginners' Zone. Last reply by John Chasse May 19.

Product Reviews

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…

Continue

Posted by Glenn Revheim on April 5, 2018 at 5:57am — 4 Comments

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…

Continue

Posted by justin waldron on April 2, 2018 at 5:46am

© 2018   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_