Kreg Owners' Community

Hello All. 

First of all, I am very pleased with all my Kreg equipment...except for one tiny annoyance. Does anyone else have problems with the square heads of the driver bits rounding off and (then of course) stripping out? I suspect technique may be contributing, but I also wish they were perhaps a bit deeper and harder. Anyone else have this problem or abe to offer any suggestions? 

Thanks in advance. 

Views: 345

Reply to This

Replies to This Discussion

Mine rounded off quite quickly, as well.  I attributed it to using an impact driver to drive the screws, some of which had space restrictions and required awkward angles.  I did pick up a couple at Rockler that had hardened tips and lasted quite a bit longer.

Thanks, Tim. The only ones I see at Rockler, however, are labelled: Kreg Jig® HD Driver Item #: 47983. Are they the ones you ordered?

Mr. Hampton, 

When driving in your screws you will want to make sure that the driver is fully engaged with the screw head.  Due to the angle the screw is being driven in at, if this is not fully engaged it will greatly increase your chance of stripping out.  We do not recommend using an impact driver when putting in your screws as this makes it easy to over drive the screws and increase your chance of stripping out as well.  While driving your screw you will want to make sure you are going at a consistent speed allowing the screw to do its work.  

The HD driver you are referring to on the Rockler page you found would not be the correct driver.  This is for our HD jig and is actually a #3 driver instead of the normal #2.  It would be too large to fit into the head of our normal screws.  If you have any other questions please let us know.  

Mine stripped quickly too. I bought Hitachi bits from Menards & never looked back.

Also rather than holding the drill like you normally would with the handle to the left or right. Turn the drill upside down,, cord or battery straight up. Just doing that helped me a lot.

Thanks, KregCS. I do try to let the screw do the work. Since you can't see the screw head and you driving at an angle, it is a bit more of a challenge to align properly. Will try harder, but will also get hardened tips. I am sure I'll improve over time. 



KregCS said:

Mr. Hampton, 

When driving in your screws you will want to make sure that the driver is fully engaged with the screw head.  Due to the angle the screw is being driven in at, if this is not fully engaged it will greatly increase your chance of stripping out.  We do not recommend using an impact driver when putting in your screws as this makes it easy to over drive the screws and increase your chance of stripping out as well.  While driving your screw you will want to make sure you are going at a consistent speed allowing the screw to do its work.  

The HD driver you are referring to on the Rockler page you found would not be the correct driver.  This is for our HD jig and is actually a #3 driver instead of the normal #2.  It would be too large to fit into the head of our normal screws.  If you have any other questions please let us know.  

Thanks, Glen. Will pick some up and try them. Thanks for the drill position tip. Will try it next time I am using the jig. 


Glen S said:

Mine stripped quickly too. I bought Hitachi bits from Menards & never looked back.

Also rather than holding the drill like you normally would with the handle to the left or right. Turn the drill upside down,, cord or battery straight up. Just doing that helped me a lot.

You're Welcome. I hope that trick works for you. I also bought some screw wax that I'm going to try on a Tiger Maple face frame.

The screw wax made driving the screws a whole lot easier!

Reply to Discussion

RSS

Need Help?

For Technical Support, call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm (CST). 

Videos

  • Add Videos
  • View All

Forum

Accu-Cut: Set Screws in Track Keep Coming Loose 1 Reply

Started by Dan Duce in Beginners' Zone. Last reply by KregRep 17 hours ago.

Is my drill speed set too high when screwing? 2 Replies

Started by Matthew Hinton in Beginners' Zone. Last reply by Matthew Hinton 2 hours ago.

Solid wood plugs too short? 2 Replies

Started by Doc JL in Other Kreg® Products. Last reply by KregCS Jan 15.

Euro hinges jig question 9 Replies

Started by Laura in Beginners' Zone. Last reply by Laura Jan 6.

Tapered Table Legs 6 Replies

Started by Pamela Anders in Beginners' Zone. Last reply by Anthony Saba Jan 12.

Product Reviews

Kreg Foreman

I have built many kitchens and finally decided to buy the Foreman, because my latest kitchen consisted of 28 cabinets and I was over my hand hurting from all the drilling, moving the clamp etc., it seemed like a smart choice.

The…

Continue

Posted by justin waldron on January 8, 2018 at 4:05am — 2 Comments

Kreg K5 Jig Review

Posted by Daris R. on November 20, 2017 at 5:39pm

© 2018   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_