Kreg Owners' Community

Kreg Jig® Operation (276)

Discussions Replies Latest Activity

Kreg drill bits

I have drilled over 500 holes with the same bit and have never had a problem. I drill 8 to 10 holes and then let the bit cool down, I inser…

Started by W. R. Willis

0 Oct 18, 2016

Cherry and Kreg Foreman

I purchased a Kreg Foreman a couple weeks back and so far, really like it. I have built a couple shop cabinets out of 3/4 oak plywood and i…

Started by DaveTinley

9 Sep 22, 2016
Reply by Jay Boutwell

1/2 inch playwood to 3/4 inch solid

Im trying to drill pocket holes in 1/2 maple playwood to be joined with 3/4 inch maple styles. I set up for 1/2 depth but the holes are not…

Started by Thomas

1 Sep 12, 2016
Reply by KregCS

What setup do I need to attach 2x material to 5/4 material?

Most of the guides I've seen for determining the setup for your Kreg jig show equal material. I am building a kids picnic table and want to…

Started by Angie Overton

3 Jun 15, 2016
Reply by Angie Overton

Pocket Hole Jig settings for metric lumber

Hi. I've actually owned my pocket hole jig for quite some time, but it has had such little use a long time ago that I'm virtually starting…

Started by Anony Mouse

2 Jun 5, 2016
Reply by Ken Kortch

Problem with K5 jig

I recently purchased the new K5 jig and read the directions about its proper use. When I attempted to raise the handle and hear the two cli…

Started by Lee Warras

4 May 22, 2016
Reply by Glen S

Screws coming through

I'm building a kitchen table with bread board ends. I built it out of 2x8's cut down to 7" wide and am putting 2x4's underneath as a "stiff…

Started by Tim Thomasson

2 May 2, 2016
Reply by KregCS

Screw size for 3/4 inch Setting

A lot of plans I have found say that you shoudl use 1.25 inch Kreg screws for holes drilled at the 3/4 inch setting.  I find that these don…

Started by Andy Harris

7 Apr 21, 2016
Reply by Robert A Edwards

Edge Joining narrow (8.5cm or 3.25") boards with a Kreg R3

Hi there, I'd like to edge join three 1" thick boards that are 8.5cm / 3.25" wide. Initially, when I tried to do this, I realised that the…

Started by Gordon Nicol

5 Apr 3, 2016
Reply by james wilhelm

Screw size for DIFFERENT sized lumber

I seem to recall from a previous post somewhere that when choosing your screw size you should select the screw for the "receiving" piece of…

Started by Steve Gronsky

46 Mar 30, 2016
Reply by Robert

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Kreg Accu-Cut and Rip-Cut 4 Replies

First off tried to mention all this to Kreg via Email and just because I live outside the USA seems that the system does not work as they say phone number invalid, which is not.OK bought a Accu-Cut and set it up no problems there worked OK both…Continue

Started by Kenneth J Hunt in Other Kreg® Products. Last reply by Kenneth J Hunt 21 hours ago.

Router bits 4 Replies

Tungsten carbide? Skill level is beginning woodworker

Started by MINICOOPERUSAF in Beginners' Zone. Last reply by Tim Grace on Monday.

R3 part

hi all can anybody help got r3 for Xmas and I have noticed that the gray tabs are different think somebody  in assembly was talking the piss day and I have 1 metric side and imperial side so they don’t match up hellllp plzericContinue

Started by Eric Kershaw in Beginners' Zone Jan 8.

Having issues with K5 5 Replies

I watched the setup videos, searched for information and spent half a day and can not get the clamp to hold.i tightened up the screws underneath in various stages up to fully tightened, makes no difference.I do not get the two clicks and I can slide…Continue

Started by Todd Caldwell in Beginners' Zone. Last reply by Glen S Jan 7.

Product Reviews

Merry Christmas r3

 Hi all Santa left me one under the tree the elf thar made it must have had a bad morning because one gray tab is metric and the other one is imperial help Santa what do I do

thanks Eric 

Posted by Eric Kershaw on January 8, 2019 at 6:27pm

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…

Continue

Posted by Glenn Revheim on April 5, 2018 at 5:57am — 4 Comments

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…

Continue

Posted by justin waldron on April 2, 2018 at 5:46am

Kreg Foreman

I have built many kitchens and finally decided to buy the Foreman, because my latest kitchen consisted of 28 cabinets and I was over my hand hurting from all the drilling, moving the clamp etc., it seemed like a smart choice.

The…

Continue

Posted by justin waldron on January 8, 2018 at 4:05am — 2 Comments

© 2019   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_