Sort by:
Discussions | Replies | Latest Activity |
---|---|---|
Help!!!Putting together the Kreg Wall Cabinets. Using 3/4" ply with 1-1/4" coarse screws. When I drilled the pocket holes I made sure that the jig… Started by Michael Busch |
2 |
Sep 19, 2014 Reply by Michael Busch |
My Special ProjectI currently have two special projects to build. One is a Hope Chest for my 19 year old daughter. I have been promising her a hope chest for… Started by Timothy L Hoff |
2 |
Sep 19, 2014 Reply by justin waldron |
Learning from the experiencedHi guys, Recently put together a face frame and noticed that most of the joints gave me a smile as they came together as intended. A co… Started by Rita B. |
5 |
Sep 19, 2014 Reply by Khalid Al-Bahi |
Drill-Torque SettingI have a Dewalt 18V that I use to place the screws. Is there a torque setting on the chuck I should use? Mine goes to 17 then drill. Or, is… Started by daddywoofdawg |
3 |
Sep 19, 2014 Reply by daddywoofdawg |
Looking for More Kreg-Friendly PlansI have been all over the internet looking for plans for using my Kreg Jig. I just bought the tool box with an assortment of screws, and nee… Started by Timothy L Hoff |
1 |
Sep 18, 2014 Reply by KregRep |
Kreg Jig HD Depth GuideI just purchased a Kreg Jig HD and am excited to start a few projects. I had a quick question I was hoping to get some help with. The HD… Started by derek |
1 |
Sep 18, 2014 Reply by KregRep |
Need help getting startedHi folks! I'm new to woodworking and I am trying to take it up to work my way out of depression. I'm a Mechanical Engineer by trade, from… Started by Nirupama Lakshminarasimhan |
5 |
Sep 18, 2014 Reply by Mark Garner |
Formula for Depthsis there a formula to use to know how deep to drill the pilot holes? Started by Robert Hodge |
2 |
Sep 18, 2014 Reply by daddywoofdawg |
My husband's workshop... I just borrow the spaceOf all the places in my marriage that is not 50-50, I would say the garage tops the list. How does one build when they don't have a place o… Started by Nicci |
0 | Sep 16, 2014 |
Good website to sell projects?Can anyone suggest a website that I can post my stuff for sale on? I'd like to keep it local, within northern California, if at all possibl… Started by craig ohlson |
7 |
Sep 13, 2014 Reply by Joshua Russell |
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service