Kreg Owners' Community

Beginners' Zone (1,258)

Discussions Replies Latest Activity

Splitting

I am Rex.  When I try to join two pieces of 13/16" cherry wood, the receiving piece splits.  I am using 1 and 1/4" fine thread screws.  Can…

Started by Rex Earl

2 Jun 2, 2011
Reply by Rex Earl

Fastening Deck Boards to Joists - Weakening Joists?

So I've already attached a few deck boards by drilling pocket holes into the joists and securing with weather resistant screws.  It strikes…

Started by Dave Bless

1 Jun 2, 2011
Reply by John Schaben

Router help

I have a new hitachi router but i have a question. I have a 3/8's round over bit that i cant get high enough into the base for it to work c…

Started by Steve Bennett

9 Jun 2, 2011
Reply by Steve Bennett

Crown Jig

Has anyone used the Kreg Crown Jig? And if so, how did it work?

Started by Roy Orosco

1 May 30, 2011
Reply by Phil Shull

Deck jig

Basically my question is a simple one....can you use the deck jig without using spacers between the boards?   I'm in the process of buildin…

Started by Ron Weeks

5 May 26, 2011
Reply by John Schaben

bar stools using 2X2 furring strips

Hi, I am new to wood working, did some projects using Kreg and got very excited. Rushed to make a stool for my daughter using 1X2 furring s…

Started by AK

5 May 25, 2011
Reply by Bev Kirk

Question on workbench

So I am getting ready to tackle my first project, the simple workbench.  I am very excited, however I had some questions.  I do not have in…

Started by Scotty Gadlin

11 May 24, 2011
Reply by John Hardin

Pilot hole depth problem

I built a simple bookcase out of 3/4" ply. I set the depth collar using the gauge on the case. I used 1 1/4" coarse screws. On some holes,…

Started by antkn33

12 May 24, 2011
Reply by Otto Johansen

Finishing Plywood Edges

Does anybody know of a good technique for finishing plywood edges without covering them?

Started by Walter Maldonado

3 May 23, 2011
Reply by Mike Camp

2x2 posts for a cabinet

Hi folks. Just bought the regular kreg jig. Never used pocket holes before Had a quick mess about and it's obvious the approach works well…

Started by Rob

0 May 19, 2011

RSS

Need Help?

For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST. 

Videos

  • Add Videos
  • View All

Forum

Kreg Accu-Cut and Rip-Cut 4 Replies

First off tried to mention all this to Kreg via Email and just because I live outside the USA seems that the system does not work as they say phone number invalid, which is not.OK bought a Accu-Cut and set it up no problems there worked OK both…Continue

Started by Kenneth J Hunt in Other Kreg® Products. Last reply by Kenneth J Hunt on Wednesday.

Router bits 4 Replies

Tungsten carbide? Skill level is beginning woodworker

Started by MINICOOPERUSAF in Beginners' Zone. Last reply by Tim Grace on Monday.

R3 part

hi all can anybody help got r3 for Xmas and I have noticed that the gray tabs are different think somebody  in assembly was talking the piss day and I have 1 metric side and imperial side so they don’t match up hellllp plzericContinue

Started by Eric Kershaw in Beginners' Zone Jan 8.

Having issues with K5 5 Replies

I watched the setup videos, searched for information and spent half a day and can not get the clamp to hold.i tightened up the screws underneath in various stages up to fully tightened, makes no difference.I do not get the two clicks and I can slide…Continue

Started by Todd Caldwell in Beginners' Zone. Last reply by Glen S Jan 7.

Product Reviews

Merry Christmas r3

 Hi all Santa left me one under the tree the elf thar made it must have had a bad morning because one gray tab is metric and the other one is imperial help Santa what do I do

thanks Eric 

Posted by Eric Kershaw on January 8, 2019 at 6:27pm

Kreg Project Center Work Station

The Kreg Project Center is great by itself, but 2 KPC's are better than 1 when you want to set up a 12 ft. work station in a couple minutes.…

Continue

Posted by Glenn Revheim on April 5, 2018 at 5:57am — 4 Comments

Festool Domino 500

The first thing I will do is set price aside and focus on the tool and why I bought the Domino. 

      I have orders for a few dining tables and chairs.  I have made one prototype chair, while I have all the tools to make angled…

Continue

Posted by justin waldron on April 2, 2018 at 5:46am

Kreg Foreman

I have built many kitchens and finally decided to buy the Foreman, because my latest kitchen consisted of 28 cabinets and I was over my hand hurting from all the drilling, moving the clamp etc., it seemed like a smart choice.

The…

Continue

Posted by justin waldron on January 8, 2018 at 4:05am — 2 Comments

© 2019   Created by KregRep.   Powered by

Badges  |  Report an Issue  |  Privacy Policy  |  Terms of Service

_