Sort by:
Discussions | Replies | Latest Activity |
---|---|---|
Renovated kitchen - floorI am planning on installing new cupboards and floating floor. The front legs would be resting on the floor and the back of the base cabine… Started by Bruce W Phillips |
11 |
May 20, 2012 Reply by Bruce W Phillips |
cabinet legsI am new to cabinetry. I am building a oak curio cabinet. I have 8" wooden legs to put on bottom. what is the best way to install them. th… Started by George Slick |
10 |
May 18, 2012 Reply by Jason Watkins |
Inexpensive sprayingI have not tried but thought i might interest some of you http://www.youtube.com/watch?v=bPoeHjr4C_k&feature=related Started by Jens Jensen |
7 |
May 18, 2012 Reply by RCW |
Kreg screw tips poking through wood...I'm a newbie ;). I've been making (or rather, attempting to make) the Kreg tool storage box using 1/2" birch plywood. The 1" screws are pok… Started by Drea |
13 |
May 13, 2012 Reply by Mike miller |
avoid splitting when driving pocket hole screws along the grain into an end piece...Even when selecting the correct setting and drill bit measurement, and screw length and type, have experience some splitting or crunching i… Started by Pierre Vallee |
2 |
May 11, 2012 Reply by Pierre Vallee |
Mixing hard and soft woods.What screws would I use to attach a maple bench top to a fir 2 x 4 frame. Started by Ernest Bennett |
2 |
May 10, 2012 Reply by Ernest Bennett |
Deck jig in plastic grooved deckingIs the kreg deck jig designed for use on new composit deck materials? Do the boards have to be the non groved? When I say groved I'm not ta… Started by Gary roofner |
19 |
May 5, 2012 Reply by Gary roofner |
Wood questionHello, I am wondering if anyone has used the jig on 3/4 x 3/4 stock. I'm looking to make some grill panels for some speaker cabinets and… Started by Jim Shelton |
7 |
May 3, 2012 Reply by Ken Darga |
turquoise grainI just picked up a truckload of mixed hardwood and what I believe to be maple has a few grains that can only be described as turquoise. Has… Started by Jim |
1 |
Apr 29, 2012 Reply by Gary roofner |
NEWBIEJUST TRIED MY KREG JIG FOR THE FIRST TIME. USED SOME LEFT OVER 5/4 RED CEDAR TO BUILD A TABLE FOR MY RAISED BED GARDEN. ALSO BUILT THE RAIS… Started by CHARLES TRAHAN |
1 |
Apr 25, 2012 Reply by RCW |
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service