Sort by:
Discussions | Replies | Latest Activity |
---|---|---|
Compound 45I can't seem to wrap my head around it. 2x 3/4 ply both cut at 45 makes a 90. I have busted thru every time. The angle is cut as if doing m… Started by Matt |
3 |
Sep 26, 2011 Reply by John Schaben |
Pocket screws and composite boardsI'm putting lattice around my deck and want to frame the lattice with pvc composit 1X 2 1/2. I was going to use the PVC glue and pocket scr… Started by Ken Fitzpatrick |
4 |
Sep 23, 2011 Reply by John Schaben |
combo belt disk sanderI am looking to get a combo belt disk sander that wont cost me a arm and leg any suggestions would be helpfull, thanks Dave Started by david r reasland |
0 | Sep 19, 2011 |
How close to ends of boards can I place a holeHello All, I am new to wood working and the Kreg system, That being said I have a question. How close to the end of the board can drill… Started by Gary Nalen |
22 |
Sep 19, 2011 Reply by Gary Nalen |
Stain producing two diffrent shades..?Hello All, I am fairly new at woodwork and have a slight problem. I have built a headboard and a bed frame. Both were built using the Kre… Started by Derrick Williams |
14 |
Sep 18, 2011 Reply by Bennett S. Reynolds |
advice needed on purchasing a multi-toolim looking into buying a multi-tool and what comes to mind would be the dremel http://www.homedepot.ca/product/dremel-multi-max-kit/916712#… Started by Joey |
49 |
Sep 16, 2011 Reply by Edward Van De Car |
New to woodworkerI am Michel Jonson from London, i am new woodworker, please give me some information about this website and its features and its working al… Started by michel jonson |
2 |
Sep 16, 2011 Reply by Al Barale |
Cabinet making guideI lost my cabinet making guide from Kreg due to a virus. Had to have my computer fixed and lost everything. Can somebody help me? Started by Roy Orosco |
2 |
Sep 12, 2011 Reply by Bob S |
Kreg cabinet jigI once saw a jig by Kreg to use while installing kitchen cabinets. I have since been unable to locate one or any information about one. C… Started by Gary Hemphill, Sr. |
1 |
Sep 11, 2011 Reply by John Schaben |
what brand router to buy??I'm looking to replace my ryobi router. It does ok for light routing, but i want a router with a little more power. I have been looking at… Started by Derrick Williams |
36 |
Sep 7, 2011 Reply by John Schaben |
For Technical Support, please call 800-447-8638 or send a message. Reps are available Monday through Friday from 8am to 5pm CST.
1 |
K5 Repair |
2 |
Keepsake Box |
3 |
Turned Wands |
4 |
Boxes |
5 |
Turned Pipes |
6 |
Pizza Cutters |
7 |
Bookmarks |
8 |
Coffin Shelf |
I making a hex ring out of 2x4s ripped to 2 ¾ inches wide with 30 degree miters. What setting on the Jig should I used? 1 ½ is too much. Thanks.Continue
Started by Patrick Halinski in Kreg Jig® Operation Dec 30, 2023.
Hi All.....I have the 35mm Kreg Jig hinge drill guide. The guide is great for 35mm Hinge Cups, but I have a speciality 40MM hinge cup to drill.Has anyone adapted the Kreg guide to work with 40mm Forsner drill bits? Or have a guide that works…Continue
Started by Ed Anderson in Beginners' Zone Oct 3, 2023.
I saw the video Kreg put out for this new jig and had high hopes for it.
I purchased one today and am very disappointed with it.
First the docking station is extremely cheap. The plastic is pathetic. A Lego has more…
ContinuePosted by Duke Leon on February 15, 2021 at 9:00pm
Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional…
ContinuePosted by Robert Ringel on September 17, 2020 at 1:48pm — 9 Comments
© 2024 Created by KregRep. Powered by
Badges | Report an Issue | Privacy Policy | Terms of Service